Encore E 3 Manuel d'utilisateur télécharger pdf (Page 2)

QUICK START USERS GUIDE

If you do not understand any part of this quick start users manual

and would like the complete version, Please visit our web site @

www.encoreautomotivesystems.com . Warranty information

and product registration can also be found at our site.

The complete manual is necessary for advanced users and not all user functions

are covered in this quick start guide.



Encore E-7s Remote Transmitter

TRANSMITTER PROGRAMMING:

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter

memory is exceeded, the security system will start deleting transmitters from memory in

chronological order.

1. Turn the Ignition 'switch ‘OFF/ON’ 4 TIMES and stay in ON position.

“Within 15 seconds”.

2. Push the Valet switch 4 times and hold it on the 4th push until a long chirp is heard then

release the valet switch. You are now in the Transmitter programming mode.

3. Press and hold any button of the transmitter until the siren responds with a confirming

chirp, indicating the signal has been stored into memory.

4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for

each transmitter.

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light

flashes will confirm exit.

Depending on the usage, the remote batteries should be changed at least once a year .

The 1-way remote, (E-7s) is powered by a pair of 3V, CR2016 batteries. These batteries are

available at most locations batteries are sold and can be replaced by the user.

TRANSMITTER OPERATION

TransmitterButton SystemFunction Remark

Button

Lock door / ARM ARM (OPTIONAL)

– Button

Arm and Delete Optional

Sensor

Press twice.

(OPTIONAL)

Button

Car Locator While System Armed.

Button for 3

seconds

Panic function Press 3 seconds to start

and stop

Button

Unlock Door / DISARM

– Button

Two Steps Door Unlock

& Disarm System

Press twice within 3

seconds. (optional

installation and

programming required)

Button for 3

seconds

Trunk Release Press 3 seconds

+ Button

Silent LOCK / UNLOCK Ignition in "OFF" position.

+ Button for 1

seconds

Activate Car-Jacking

(OPTIONAL)

Ignition in "ON" position.

SILENT LOCK /

UNLOCK Programmable

Switching code For 2nd

Car Operation.

Press & hold until TX

LED on

ACTIVE LOCKING – LOCK & ARMING:

1. Press

button on transmitter.

2. The siren or horn will chirp once and the parking lights will flash once indicating that the system is

now armed. The vehicle doors will lock upon arming when interfaced with the security system.

Note: Defective sensor reminder: If the siren or horn sounds 3 chirps, then you have left a door,

trunk, or hood lid ajar.

SILENT LOCKING AND UN-LOCKING: ARMING / DISARMING: Press the

button together on

the transmitter to LOCK or UNLOCK your security system, No chirp sound will be heard; arm / disarm

confirmation will be through the vehicles parking lights only.

SHOCK SENSOR BY-PASS: Pressing the

button on the transmitter twice within 3 seconds will arm

the security system and by-pass the shock sensor. The system will chirp one additional time to confirm

the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one

arming cycle only. The security system will return to normal operation during the next arming cycle

PASSIVE LOCKING OR ARMING: Programmable

Active arming / disarming is controlling your security system via the remote transmitter. This security

system is equipped with an optional Passive Arming feature, which allows the security system to arm

30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you

reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing

again once all vehicle entrances are closed.

3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren or

horn will chirp [1] time and the parking lights will flash [1] time.

PASSIVE DOOR LOCKING: Programmable

The vehicle doors will automatically lock after passive arming cycle has been completed.

ACTIVE UN-LOCKING: – UNLOCK & DISARM:

1. Press the

button on the transmitter.

2. The siren or horn will chirp twice and parking lights will flash twice to indicate that the security

system is now disarmed. The vehicle doors will unlock when interfaced with the security system.

TAMPER DISARMING: (OPTIONAL). If the alarm is triggered; Upon disarming the system the siren or

horn will chirp 4 times and parking lights will flash 3 times. This will indicate that the alarm has been

triggered while armed.

TWO STEP DOOR UNLOCK: (OPTIONAL) This feature will independently unlock the driver’s door

only when disarming the security system. Pushing the

button on the transmitter a second time

within 3 seconds will unlock the entire vehicle. Optional installation required.

AUTOMATIC RE-LOCKING or RE-ARM: If this feature is selected, the security system will

automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will

cancel if any door is opened before the 60

seconds timer has elapsed.

DISARMING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 10 seconds push and release the valet switch

The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle

normally.

VALET MODE:

The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand

your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all

alarm functions are bypassed, however, the remote panic feature and remote door locks will remain

operational.

Enter Valet Mode:

1. Turn the ignition to “ON” position.

2. Push and hold valet switch for 2 seconds or until the LED turns on. The LED will remain on as

long as the system is in 'valet mode'.

Exit Valet Mode:

1. Return to normal operation, turn ignition 'ON'.

2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting the

valet mode.

PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.

1. Press and hold the

button on the transmitter for 3 seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the

button for 3 seconds on the transmitter, the panic mode will be

turned off immediately.

3. If the button is not pressed, the alarm will automatically stop after 30 seconds.

TRIGGER THE SYSTEM:

When armed, your vehicle is protected as follows:

1. Light impacts will trigger the warn-away signal. A long chirp from siren /horn.

2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will trigger the

programmed sequence.

The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren or horn and parking

lights will turn on to alert of an intrusion for 30 seconds. Then the siren or horn will stop and automatically reset

and re-arm. If any the sensors or detectors are still active, the alarm system will sound a maximum of three-30

second cycles.

ANTI CAR-JACKING: (OPTIONAL) If alarm option is installed.

Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature is

“OFF”. This system is default setting Car-jacking “OFF”.

1. TRANSMITTER ACTIVATED THE CAR JACKING:

Press and hold

+ button on the transmitter for 1 second while the vehicle’s ignition is ON. The parking

light will turns on for 1.5” seconds to indicate carjacking activated.

2. DOOR SWITCH ACTIVATED CAR JACKING:

1. Turn the ignition switch to “ON” position, the system is armed.

2. Once the system is armed, if you are forced from the vehicle, the system will active the car jacking trigger

when the door is opened and closed while the ignition is “ON”.

TRIGGER THE CAR JACK MODE:

3-timer circuits will function as follows:

First timer:

a. 50 seconds after the system has been triggered. The siren or horn will start chirping for 15 seconds.

b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the

car-jacking feature.

c. If not, it will enter second timer car jacking.

Second timer:

65 seconds after the system has been triggered. The siren or horn starts alarming and the parking light

starts flashing.

Third timer:

90 seconds after the system has been triggered

a. The siren or horn will still be alarming and the parking light flashing.

b. The starter disable will activate to prevent the vehicle from starting.

c. It will remain active until the vehicle's battery power exhausted.

OVERRIDE THE SYSTEM TO TURN OFF CAR JACKING:

Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch. The siren or horn will

stop and the system will be disarmed

IGNITION CONTROL DOOR LOCKS.

If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the

vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned

“OFF”.

TRUNK RELEASE: Press and hold

button on transmitter for three seconds to remote control the trunk

release or other electric devices.

CAR LOCATOR: Press the

button on the transmitter when the vehicle is in the armed / locked mode to active

car locator function. The siren or horn will chirp 6 times. The parking light will flash 12 times, allowing you to easily

locate your car.

SHOCK SENSOR ADJUSTMENT

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.

2. Push the Valet switch 5 times holding in on the 5th push until a long chirp is heard. Then release the valet

switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode.

3. Press and hold

button for 2 seconds. One long siren or horn chirp to indicate the unit is ready to accept

adjustments of the shock sensor.

4. Press

button on the transmitter once. This will decrease the sensitivity level by one step. Each time the

button is pushed, a decrease is made the siren /horn chirp will respond with [1] chirp, while 2 chirp indicates

the shock sensor is OFF.

5. Press

button on the transmitter once. This will increase sensitivity level by one step. Each time an increase

is made the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates maximum sensitivity.

6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor.

a). Activate the warn-away (first stage the shock sensor), the siren or horn will emit a short chirp.

b). Activate the full alarm (second stage the shock sensor), the siren or horn will emit a long chirp.

7. When you are satisfied with the setting, press the

button to lock in the adjustment. One long siren or horn

or horn chirp will indicate the unit has locked in the adjustment.

Note: If 30 seconds of inactivity expires, or you turn on the ignition during of above steps, the unit will exit the

program mode and return to the disarmed mode. Three long chirps will confirm exit.

1 2

Commentaires sur ces manuels

Pas de commentaire

Encore E 3 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Électronique des véhicules automobiles Encore E 3